Skip to main content

Launch X431 IMMO Plus vs X431 V+ vs PAD VII+ GIII

Launch X431 X-prog3 aka GIII is used to program BMW Benz VAG Porsche keys and clone/replace ECU/TCU modules. What’s the difference among Launch X431 IMMO Plus, IMMO Elite, X431 V+ and X431 PAD VII with Xprog3?

 

Check table comparison below:

ItemLaunch X431 IMMO Elite


Launch X431 IMMO Plus


Launch X431 V+ and X-prog3Launch X431 PAD VII and X-prog3
Read immobilizer passwordYesYesYesYes
Ignition key learningYesYesYesYes
Benz BMW VAG Porsche key programmingYesYesYesYes
ECU Gearbox TCU Cloning (IMMO Prog)YesYesNoYes
Anti-theft password car coverageMoreMoreLessLess
Nissan B18 Immo replacement without passwordYesYesNoNo
Toyota all keys lost (pre-2022)YesYesNoNo
Volvo all keys lost (-2022)YesYesNoNo
Peugeot all keys lostYesYesNoNo
Citroen all keys lost/ module replacementYesYesNoNo
Independent IMMO function for each car brandsYesYesNoNo
Basic diagnostic functionYesYesYesYes
Active Test (Di-directional)YesYesYesYes
Special function under each car brandsNo, no VAG guided function, Renault special function under Diagnostic.YesYesYes
Common Service reset functionsYesYesYesYes
Guided functionNoNoNoYes
Online programmingNoNoNoYes
Update2 Years free update2 Years free update2 Years free update2 Years free update

In sum:

  • IMMO Plus has the same key programming and ECU/TCU clone function as IMMO Elite. The difference between these two is that IMMO Elite has basic diagnostics but IMMO plus has full diagnostics.
  • IMMO tablets support newer vehicle immo programming, i.e Volvo pre-2022, Toyota pre-2022, X431 V+ and PAD VII do not.
  • Pad VII supports online programming, others do not.
  • To clone or replace ECU or gearbox TCU with X-prog3, your tablet should have the ability to connect via USB. Launch X431 V+ only connects via Bluetooth, so V431 v+ with G III cannot clone ECU/TCU.

V431 v+ with G III cannot clone ECU/TCU

X-prog3 supports following ECU/TCU cloning function:

Launch X431 X-prog3 aka GIII is used to program BMW Benz VAG Porsche keys and clone/replace ECU/TCU modules. What’s the difference among Launch X431 IMMO Plus, IMMO Elite, X431 V+ and X431 PAD VII with Xprog3? Check table comparison below: Item Launch X431 IMMO Elite X431 Immo Elite Launch X431 IMMO Plus X431 Immo Plus Launch X431 V+ and X-prog3 X431 V And Xprog3 Launch X431 PAD VII and X-prog3 X431 Pad Vii And Xprog3 Read immobilizer password Yes Yes Yes Yes Ignition key learning Yes Yes Yes Yes Benz BMW VAG Porsche key programming Yes Yes Yes Yes ECU Gearbox TCU Cloning (IMMO Prog) Yes Yes No Yes Anti-theft password car coverage More More Less Less Nissan B18 Immo replacement without password Yes Yes No No Toyota all keys lost (pre-2022) Yes Yes No No Volvo all keys lost (-2022) Yes Yes No No Peugeot all keys lost Yes Yes No No Citroen all keys lost/ module replacement Yes Yes No No Independent IMMO function for each car brands Yes Yes No No Basic diagnostic function Yes Yes Yes Yes Active Test (Di-directional) Yes Yes Yes Yes Special function under each car brands No, no VAG guided function, Renault special function under Diagnostic. Yes Yes Yes Common Service reset functions Yes Yes Yes Yes Guided function No No No Yes Online programming No No No Yes Update 2 Years free update 2 Years free update 2 Years free update 2 Years free update In sum: IMMO Plus has the same key programming and ECU/TCU clone function as IMMO Elite. The difference between these two is that IMMO Elite has basic diagnostics but IMMO plus has full diagnostics. IMMO tablets support newer vehicle immo programming, i.e Volvo pre-2022, Toyota pre-2022, X431 V+ and PAD VII do not. Pad VII supports online programming, others do not. To clone or replace ECU or gearbox TCU with X-prog3, your tablet should have the ability to connect via USB. Launch X431 V+ only connects via Bluetooth, so V431 v+ with G III cannot clone ECU/TCU. X431 Immo Plus Usb Connection X-prog3 supports following ECU/TCU cloning function: X Prog3 Ecu Clone

Labels:

Comments

Post a Comment

Popular posts from this blog

Install Launch X431 SmartLink C J2534 Driver

Launch X431 SmartLink C can be used as a J2534 PassThru device, working together with the PC installed with the OEM diagnostic software to perform the J2534 reprogramming.   Obdii365   shows where to download and how to install the Passthru SAE J2534 driver for LAUNCH X431 Smart Link C passthru adapter (for   PAD VII ) If you have Smartbox 3.0 (old PAD V and   X431 Pro5 ), download J2534 passthru   in the previous post .     How to Download Launch X431 SmartLink C J2534 passthru driver?   Same as smartbox 3.0, you need both installation programs (setup driver and PC tool for update).   1. Download PC tool for update (update smartlink c firmware) Visit   https://en.cnlaunch.com/ Select Products tab->X-431 PAD VII Pull down product information and find   Download Download   Smartlink J2534.zip Install Launch J2534 PC tool Run LAUNCH J2534 program on desktop. Now you can check Smartlink adapter version and update firmware 2. Do...
Post a Comment
Read more

Will Lauch X-PROG3 Work with Diagzone, Xdiag or Prodiag?

Does Launch X431 X-prog3 work with xdiag, diagzone or prodiag activations?  Diagzone compatible xprog3? Is it working with prodiag? Will it work with xdiag? These are frequently asked questions of   Launch X-PROG3   (also called GIII) programmers. X-prog3 is compatible with Multiple X-431 Series   X-431 V ,  X-431 V+ ,   X431 Pro5 ,  X431 ProS ,   X431 Pro3s+ ,  X-431 PAD V ,  X-431 PAD VII , X-DIAG Pro3 diagnostic tablets. This programmer works not only for programming keys, but for working with ECU and gearbox. But when comes to key programming you need to know what you doing there is not too much info in the Diagzone/Prodiag software.   What worked and failed? Here are user reviews. *You are at your risk. We don’t provide technical support to 3rd party software.   Prodiag: Yes It works with prodiag. Prodiag provides usb connection with virtual comport. It works fine to read ECU and gearbox clone. For example, VAG DQ200 gearb...
Post a Comment
Read more

How to Make Porsche Coding Changes with Launch CRP919X CRP919E

 Instructions on Make Porsche Coding Changes using a Launch CRP919X , CRP919E , CRP919X BT , CRP919E BT scanners. Plugin X431 into OBD 2 Port, Turn Key to Accessory Mode and Wait until VIN is Determined then Hit the Back Arrow in the Upper Left Until You Get to the Next Screen Shown Below  Then select Diagnose (Although you may want to update the unit if updates are available) Then Scroll Down and select Porsche Then Select OK Then Select Automatically Search The Unit should determine the type of 718 you have and then Select OK Then Select System Selection Then Select the appropriate System for the Code you want to adjust (Note: This is the system listed in the instructions below such as Front-end Electronics, Rear-End Electronics, Instrument Cluster or Air Conditioning) Then select Code/Brush Hiding Then select Brush Hidden/Modified Then find the Code you want to adjust (These are the Codes in the instructions below) Then Make the Change Then Hit the Write Code Button
Post a Comment
Read more