Skip to main content

Launch X-prog5 Update Simos 18.1 Data Cloning Function

Launch X431 released new immobilizer software on October 20th, 2026.

 

SOFTWARE UPDATE BY VEHICLE MODELS

Applied to Launch X431 IMMO Plus/ IMMO Elite/ IMMO PAD/ PAD series + IMMO software.

BRANDVERSIONFUNCTION
NissanV11.26Added IMMO password reading (by chip removal), key matching, and body control module (HFM) replacement functions for the 2025 Nissan Kicks.
MG (SAIC)V10.30Added key matching function for MG4X. Added key matching, alcohol interlock deactivation and alcohol interlock activation functions for MG S6 EV.
JACV10.50Added key matching functions for JAC Refine RF8, Refine RH8 PHEV, Yiwei 3, QX PHEV, Xingrui Series 7, pickup T8 PRO, and pickup T9 EV.
SaabV10.20Added key matching function for Saab 9-2. Added key adding and all-keys-lost matching functions for Saab 9-7. Added IMMO matching functions for Saab 9-3, 9-5 (1997-2010), and 9-5 Sport (2003-2012).

 

VEHICLE-MODEL SOFTWARE REQUIRING Launch X-PROG5 HARDWARE

BRANDVERSIONFUNCTION
Mercedes-BenzV10.80Added key disable function for Mercedes-Benz 4th-generation IMMO. Added all-keys-lost password calculation and key matching function for W463 (CAN). Added key frequency detection function. Added 3rd-generation transmission (TCU) read and erase functions. Added key adding, all-keys-lost matching and password reading for W230 lock (CHIP method). Added all-keys-lost matching and password reading for 215K / 220K (CHIP method). Added lock matching key reading via CHIP method.
Land RoverV10.55Added mechanical key chip-out MCU file read and write-start function for Discovery 3 (2004-2009), Range Rover (2006-2009), and Range Rover Sport (2005-2009).

 

SOFTWARE UPDATE FOR IMMOBILIZER PROGRAMMER V12.30

FUNCTIONSSUPPORTED DEVICES
Added wireless dealer-key generation for Volkswagen 5C/5DX-PROG5
Added BOOT-mode engine ECU read/write for Magneti Marelli 4DF, 4GF, 4GV and 4SF
Added BENCH-mode read/write for Magneti Marelli engine ECUs 4AF, 6JF, 6JO, 7GF, 8F3, 9GV and 10GF
Added Jaguar BCM data read/write with NXP MC9S12XET256
Added Jeep/Ford BCM data read/write with Renesas R7F701056

 

X-431 ECU CLONE SOFTWARE V10.76

FUNCTIONSSUPPORTED DEVICES
Added 8F3 KWP protocol reset function.X-PROG5
/ X-431 ECU & TCU Programmer
/ X-PROG3 PC Adaptor
Added Simos18.1 anti-theft data cloning function.
Added Simos18.7 BOOT mode data read/write function.

Launch X-prog5 Update Simos 18.1 Data Cloning 1
Launch X-prog5 Update Simos 18.1 Data Cloning 2


Labels:

Comments

Post a Comment

Popular posts from this blog

Install Launch X431 SmartLink C J2534 Driver

Launch X431 SmartLink C can be used as a J2534 PassThru device, working together with the PC installed with the OEM diagnostic software to perform the J2534 reprogramming.   Obdii365   shows where to download and how to install the Passthru SAE J2534 driver for LAUNCH X431 Smart Link C passthru adapter (for   PAD VII ) If you have Smartbox 3.0 (old PAD V and   X431 Pro5 ), download J2534 passthru   in the previous post .     How to Download Launch X431 SmartLink C J2534 passthru driver?   Same as smartbox 3.0, you need both installation programs (setup driver and PC tool for update).   1. Download PC tool for update (update smartlink c firmware) Visit   https://en.cnlaunch.com/ Select Products tab->X-431 PAD VII Pull down product information and find   Download Download   Smartlink J2534.zip Install Launch J2534 PC tool Run LAUNCH J2534 program on desktop. Now you can check Smartlink adapter version and update firmware 2. Do...
Post a Comment
Read more

Will Lauch X-PROG3 Work with Diagzone, Xdiag or Prodiag?

Does Launch X431 X-prog3 work with xdiag, diagzone or prodiag activations?  Diagzone compatible xprog3? Is it working with prodiag? Will it work with xdiag? These are frequently asked questions of   Launch X-PROG3   (also called GIII) programmers. X-prog3 is compatible with Multiple X-431 Series   X-431 V ,  X-431 V+ ,   X431 Pro5 ,  X431 ProS ,   X431 Pro3s+ ,  X-431 PAD V ,  X-431 PAD VII , X-DIAG Pro3 diagnostic tablets. This programmer works not only for programming keys, but for working with ECU and gearbox. But when comes to key programming you need to know what you doing there is not too much info in the Diagzone/Prodiag software.   What worked and failed? Here are user reviews. *You are at your risk. We don’t provide technical support to 3rd party software.   Prodiag: Yes It works with prodiag. Prodiag provides usb connection with virtual comport. It works fine to read ECU and gearbox clone. For example, VAG DQ200 gearb...
Post a Comment
Read more

Launch X431 V+ or PIWIS-III for Porsche Diagnosis?

I have the Launch X431 V+ Pros Mini which I purchased new from obdii365 for $1079. I also have a PIWIS III clone V38.90 that i purchased from another website for $1429. I purchased the Launch X431 V+ with the intent of using it to flash a used control module for my car. When I discovered that the Launch X431 V+ could not do that I purchased a PIWIS III clone with the intention of selling the Launch X431 V+ but I have not got around to selling it yet because it is so much easier to use then the PIWIS III.Here is what I have done so far with each one. Launch X431 V+ : Cleared all the fault codes stored in the car. Activated the Aux setting in PCM (PCM/CDR) I had to add an aux cable to the PCM to make use of this one. Changed the number of flashes for one touch turn signal from 3 to 5 (Front-end Electronics) Activated Comfort entry windows up/down via keyfob (Front-end Electronics) Changed the speed when the doors auto lock, 3 mph to 20 mph (Front-end electronics) Changed the speed when...
Post a Comment
Read more