Skip to main content

Launch X431 Pro5 Smartlink vs X431 Pro3 V+ Elite Smartlink

What is the difference between Launch X431 PRO 5 with smartlink and Launch X431 PRO3 V+ Elite with smartlink? 

Check the table comparison below:

ItemLaunch X431 Pro5 SmartLinkLAUNCH X431 PRO3 V+ ELITE
Imagelaunch x431 pro5 smartlinklaunch x431 pro3 v elite
Operating systemAndroid 10.0Android 10.0
CPU2.0GHz 4-core2.0GHz 4-core
Internal memory4GB4GB
Storage64GB64GB
Screen10.1 1280*800 full HD10.1 inches 1280*800
Battery6300mAh6300mAh
WiFi2.4 and 5Ghz2.4 and 5Ghz
Cameras8MP rear camera8MP rear camera
ProtocolJ2534/DOIP/CANFD/HDJ2534/DOIP/CANFD/HD
IP RestrictionNo IP RestrictionsNo IP Restrictions
Full Bidirectional Active TestYesYes
Full system diagnosticYesYes
Dual diagnostic ModeYes, local diagnostics and super remote diagnosticsYes, local diagnostics and super remote diagnostics
Topology MappingYesYes
Pin Detection
Yes
ECU CodingYesYes
Service Function50 service reset: ABS Bleeding/TPS/Oil light service reset/EPB/TPMS/CVT/SAS/Battery Registration/IMMO/Suspension reset/Sunroof reset and etc.37 service reset: ABS Bleeding/TPS/Oil light service reset/EPB/TPMS/CVT/SAS/Battery Registration/IMMO/Suspension reset/Sunroof reset and etc.
VAG guided functionYesYes
Online programmingBenz and BMW online programming–
VCISmartLink C 2.0SmartLink C 2.0
Super Remote DiagnosticsYes, with Smartlink 2.0 and Smartlink remote diagnosis licenseYes, with Smartlink 2.0 and Smartlink remote diagnosis license
VCI ParameterCortex-A7+Cortex-M7

Linux OS

RAM 256M

ROM 8GB

3.5 inch touch screen

WiFi: 2.4GHz/5GHz dual-band

 

Display: 3.97-inch TFT screen
Resolution: 320*480
Memory: 256M
Storage: 8GB
Operating voltage: DC 9~36V
Power consumption: <6W
Local diagnosis mode: Bluetooth/wired
Remote diagnosis mode: Ethernet
Operating temperature: -10~50℃
Size: 200mm*110mm*47mm
ConnectionWiFi/USB/BluetoothWiFi/USB/Bluetooth
FCA AutoAuth Access Security Gateway (SGW)YesYes
Passthru J2534 programmingYesYes
DoIP/CAN FDYesYes
Adaptation, codingYesYes
ADAS calibration functionsOptionalOptional
TPMS functionsTSGUN/i-TPMSTSGUN/i-TPMS
IMMO programmingX-PROG3X-prog3
Add Modules to Expand FeaturesADAS Calibration Toolkit; VSP-600 VideoScope; X431 TPMS TSGUN; BST360 Bluetooth Battery Tester; X-PROG3 Immobilizer, WiFi printer, heavy duty, X431 key programmer, O2-2 scopebox, S2-2- sensor box, EV diagnostic kit, MultimeterADAS Calibration Toolkit; VSP-600 VideoScope; X431 TPMS TSGUN; BST360 Bluetooth Battery Tester; X-PROG3 Immobilizer, WiFi printer, heavy duty, X431 key programmer, O2-2 scopebox, S2-2- sensor box, EV diagnostic kit, Multimeter
HD Supportoptional HD truck packageoptional HD truck package
Update2 Years free update2 years free update
Vehicle coverage150+Brands Vehicles from 1996-2022, Support HD protocol150+Brands Vehicles from 1996-2022, Support HD protocol
AutoVIN ScanYesYes
WiFi PrinterOptionalOptional

In sum:

The biggest difference is that Pro5 Smartlink can do Benz and BMW built-in online programming, while Pro3 V+ Elite cannot.

They have the same configuration on tablet hardware and both have smartlink c 2.0 VCI.

They both support the same add-on modules, TPMS, EV, IMMO, sensor box, videoscope etc.

Labels:

Comments

Post a Comment

Popular posts from this blog

Install Launch X431 SmartLink C J2534 Driver

Launch X431 SmartLink C can be used as a J2534 PassThru device, working together with the PC installed with the OEM diagnostic software to perform the J2534 reprogramming.   Obdii365   shows where to download and how to install the Passthru SAE J2534 driver for LAUNCH X431 Smart Link C passthru adapter (for   PAD VII ) If you have Smartbox 3.0 (old PAD V and   X431 Pro5 ), download J2534 passthru   in the previous post .     How to Download Launch X431 SmartLink C J2534 passthru driver?   Same as smartbox 3.0, you need both installation programs (setup driver and PC tool for update).   1. Download PC tool for update (update smartlink c firmware) Visit   https://en.cnlaunch.com/ Select Products tab->X-431 PAD VII Pull down product information and find   Download Download   Smartlink J2534.zip Install Launch J2534 PC tool Run LAUNCH J2534 program on desktop. Now you can check Smartlink adapter version and update firmware 2. Do...
Post a Comment
Read more

Will Lauch X-PROG3 Work with Diagzone, Xdiag or Prodiag?

Does Launch X431 X-prog3 work with xdiag, diagzone or prodiag activations?  Diagzone compatible xprog3? Is it working with prodiag? Will it work with xdiag? These are frequently asked questions of   Launch X-PROG3   (also called GIII) programmers. X-prog3 is compatible with Multiple X-431 Series   X-431 V ,  X-431 V+ ,   X431 Pro5 ,  X431 ProS ,   X431 Pro3s+ ,  X-431 PAD V ,  X-431 PAD VII , X-DIAG Pro3 diagnostic tablets. This programmer works not only for programming keys, but for working with ECU and gearbox. But when comes to key programming you need to know what you doing there is not too much info in the Diagzone/Prodiag software.   What worked and failed? Here are user reviews. *You are at your risk. We don’t provide technical support to 3rd party software.   Prodiag: Yes It works with prodiag. Prodiag provides usb connection with virtual comport. It works fine to read ECU and gearbox clone. For example, VAG DQ200 gearb...
Post a Comment
Read more

How to Make Porsche Coding Changes with Launch CRP919X CRP919E

 Instructions on Make Porsche Coding Changes using a Launch CRP919X , CRP919E , CRP919X BT , CRP919E BT scanners. Plugin X431 into OBD 2 Port, Turn Key to Accessory Mode and Wait until VIN is Determined then Hit the Back Arrow in the Upper Left Until You Get to the Next Screen Shown Below  Then select Diagnose (Although you may want to update the unit if updates are available) Then Scroll Down and select Porsche Then Select OK Then Select Automatically Search The Unit should determine the type of 718 you have and then Select OK Then Select System Selection Then Select the appropriate System for the Code you want to adjust (Note: This is the system listed in the instructions below such as Front-end Electronics, Rear-End Electronics, Instrument Cluster or Air Conditioning) Then select Code/Brush Hiding Then select Brush Hidden/Modified Then find the Code you want to adjust (These are the Codes in the instructions below) Then Make the Change Then Hit the Write Code Button
Post a Comment
Read more