Skip to main content

Launch CRP919E and Thinkdiag Difference

Thinkdiag could do everything the Laucnh CRP919E scanner could do? What’s the difference between them?

 

Check the table comparison below:

*The CRP919E and CRP919X are i identical.

ItemThinkdiagLaunch CRP919E/CRP919X
SystemAndroid 5.1/iOS 9.0Android 10.0
Software AppThinkdiag 
Screen–7 inch
Storage–3G/32G
Battery–Built-in 6100 mAh Lithium Battery
Camera Function–Yes
ConnectionBluetoothUSB
Car brand Software115 car brands150 car brands
Service reset function1631
OBD2 function10 OBD2 full function10 OBD2 full function
Full system diagnosticYesYes
ECU CodingYesYes
Update1 year free update, $70 year later2 Years Free Update, One-Click WiFi Update, $199 per year later
Language10 Language optional11 Languages Optional
Live data graph4 Data display in 1 Graph8-in-1 Live Data Stream Graphing
Print reportYesYes
FCA Autoauth–Yes
DoIP–Yes
CAN FD–Yes
Battery test–Yes with BST-360

 

Thinkdiag service function list:

1.Oil Reset Service
2.Steering Angle Calibration
3.Electronic Parking Brake Reset
4.Battery Register & Battery Maintenance
5.ABS Bleeding
6.Electronic Throttle Position Reset & Learn
7.Diesel Particulate Filter (DPF) Regeneration
8.Tire Pressure Monitor System Reset
9.Anti-theft Matching
10.Injector matching
11.Air Suspension Reset
12. Gearbox Reset
13.Sunroof RESET
14.AFS Reset
15.EGR Reset
16.Gear Learning

 

 

Launch CRP919E/CRP919X Service function list:

  • Steering Angle Reset
  • Injector Coding
  • IMMO M
  • DPF Regeneration
  • A/C relearn
  • ABS Bleeding
  • AdBlue Reset
  • Throttle Matching
  • TPMS Reset
  • Tire Reset
  • AFS Headlamp Reset
  • Sunroof Initialization
  • Battery Reset
  • Seat Calibration
  • A/F Reset:
  • Oil Reset
  • GEARBOX LEARN
  • Transport Mode
  • Windows Calibration
  • Language Change
  • Suspension Reset
  • NOx Sensor Reset
  • Stop/Start Reset:
  • Coolant Bleeding
  • Brake Reset
  • Gear Learning
  • RESET EGR/EGR adaption
  • RESET HVOLBAT (High Voltage Battery Detection)
  • RESET ENGPBM
  • CCS(Cruise Control System) Calibration,
  • GPF(Gas Particular Filter) Regeneration,
  • Cylinder Power Balance Test

 

In sum:

Thinkdiag and CRP919E diagnostics and ecu coding function are almost the same. CRP919E new hardware supports CAN FD, DoIP protocols for new vehicles. It does much more special functions than thinkdiag. With CRP919E you can also access to FCA autoauth. 

When use the CRP919x to take a picture of a code, it contained the name of the module that the code was in. On the Thinkdiag, the code does not contain the name of module.

Also, the Thinkdiag does not have a screen so you will need an Android phone or tablet. There is an IOS app but you can not code with the IOS app.

Labels:

Comments

Post a Comment

Popular posts from this blog

Install Launch X431 SmartLink C J2534 Driver

Launch X431 SmartLink C can be used as a J2534 PassThru device, working together with the PC installed with the OEM diagnostic software to perform the J2534 reprogramming.   Obdii365   shows where to download and how to install the Passthru SAE J2534 driver for LAUNCH X431 Smart Link C passthru adapter (for   PAD VII ) If you have Smartbox 3.0 (old PAD V and   X431 Pro5 ), download J2534 passthru   in the previous post .     How to Download Launch X431 SmartLink C J2534 passthru driver?   Same as smartbox 3.0, you need both installation programs (setup driver and PC tool for update).   1. Download PC tool for update (update smartlink c firmware) Visit   https://en.cnlaunch.com/ Select Products tab->X-431 PAD VII Pull down product information and find   Download Download   Smartlink J2534.zip Install Launch J2534 PC tool Run LAUNCH J2534 program on desktop. Now you can check Smartlink adapter version and update firmware 2. Do...
Post a Comment
Read more

Will Lauch X-PROG3 Work with Diagzone, Xdiag or Prodiag?

Does Launch X431 X-prog3 work with xdiag, diagzone or prodiag activations?  Diagzone compatible xprog3? Is it working with prodiag? Will it work with xdiag? These are frequently asked questions of   Launch X-PROG3   (also called GIII) programmers. X-prog3 is compatible with Multiple X-431 Series   X-431 V ,  X-431 V+ ,   X431 Pro5 ,  X431 ProS ,   X431 Pro3s+ ,  X-431 PAD V ,  X-431 PAD VII , X-DIAG Pro3 diagnostic tablets. This programmer works not only for programming keys, but for working with ECU and gearbox. But when comes to key programming you need to know what you doing there is not too much info in the Diagzone/Prodiag software.   What worked and failed? Here are user reviews. *You are at your risk. We don’t provide technical support to 3rd party software.   Prodiag: Yes It works with prodiag. Prodiag provides usb connection with virtual comport. It works fine to read ECU and gearbox clone. For example, VAG DQ200 gearb...
Post a Comment
Read more

How to Make Porsche Coding Changes with Launch CRP919X CRP919E

 Instructions on Make Porsche Coding Changes using a Launch CRP919X , CRP919E , CRP919X BT , CRP919E BT scanners. Plugin X431 into OBD 2 Port, Turn Key to Accessory Mode and Wait until VIN is Determined then Hit the Back Arrow in the Upper Left Until You Get to the Next Screen Shown Below  Then select Diagnose (Although you may want to update the unit if updates are available) Then Scroll Down and select Porsche Then Select OK Then Select Automatically Search The Unit should determine the type of 718 you have and then Select OK Then Select System Selection Then Select the appropriate System for the Code you want to adjust (Note: This is the system listed in the instructions below such as Front-end Electronics, Rear-End Electronics, Instrument Cluster or Air Conditioning) Then select Code/Brush Hiding Then select Brush Hidden/Modified Then find the Code you want to adjust (These are the Codes in the instructions below) Then Make the Change Then Hit the Write Code Button
Post a Comment
Read more