Skip to main content

Launch X-prog3 Clone Audi Simos 8.51 ECU

Here is the user working experience and tips to clone Audi Simos 8.51 ECU with Launch X-prog3.

 

Trying to clone a simos 8.51 module ( from a 2013 Audi A8 ctub) with the Launch X431 IMMO Plus with x-prog3.

 

You can see simos 8.5 is supported and he successfully backed up the eeprom and flash from the original ecu and loaded it into the donor but the vehicle does not start and has a fault code saying the immobilizer is active and ecu is locked.

He even tried it with the topdon phoenix same thing. Additionally, when you auto scan the vehicle with the donor module installed it now says eeprom while trying to pull the vin.

Launch X-prog3 Clone Audi Simos 8.51 ECU  1

Launch X-prog3 Clone Audi Simos 8.51 ECU  2

Launch X-prog3 Clone Audi Simos 8.51 ECU  3

Launch X-prog3 Clone Audi Simos 8.51 ECU  4

Tips 1:

For Audi ecu you have to navigate to the year make module under scan then special functions-> antitheft and in there it shows you to pull the original ecu data and the donor data and it needs to be decrypted.

He went under service and immo prog which doesn’t tell you this and that screwed him up because he corrupted the donor ecu data flashing over it without saving it first lesson learned.

Then he was able to decrypt the original ecu data and program the donor on the bench and the vehicle starts / runs and has a vin number but now has a P160A fault code.


p160A says to reprogram and code ECU and test.

He did try reprogramming and updating the software level.

 

Tips 2:

It is the otp. You lost original pflash. You should not try to write whole p&d flash directly. Just immo data to clone VW ECU.

VW ECU has OTP area. So when need to clone vw ECU. Decrypt file and change just pin, Mac, CS, VIN (depend on which ECU you’re working with.) Some are just vin&cs.

Pay attention on password.

Comments

Popular posts from this blog

Install Launch X431 SmartLink C J2534 Driver

Launch X431 SmartLink C can be used as a J2534 PassThru device, working together with the PC installed with the OEM diagnostic software to perform the J2534 reprogramming.   Obdii365   shows where to download and how to install the Passthru SAE J2534 driver for LAUNCH X431 Smart Link C passthru adapter (for   PAD VII ) If you have Smartbox 3.0 (old PAD V and   X431 Pro5 ), download J2534 passthru   in the previous post .     How to Download Launch X431 SmartLink C J2534 passthru driver?   Same as smartbox 3.0, you need both installation programs (setup driver and PC tool for update).   1. Download PC tool for update (update smartlink c firmware) Visit   https://en.cnlaunch.com/ Select Products tab->X-431 PAD VII Pull down product information and find   Download Download   Smartlink J2534.zip Install Launch J2534 PC tool Run LAUNCH J2534 program on desktop. Now you can check Smartlink adapter version and update firmware 2. Do...

Will Lauch X-PROG3 Work with Diagzone, Xdiag or Prodiag?

Does Launch X431 X-prog3 work with xdiag, diagzone or prodiag activations?  Diagzone compatible xprog3? Is it working with prodiag? Will it work with xdiag? These are frequently asked questions of   Launch X-PROG3   (also called GIII) programmers. X-prog3 is compatible with Multiple X-431 Series   X-431 V ,  X-431 V+ ,   X431 Pro5 ,  X431 ProS ,   X431 Pro3s+ ,  X-431 PAD V ,  X-431 PAD VII , X-DIAG Pro3 diagnostic tablets. This programmer works not only for programming keys, but for working with ECU and gearbox. But when comes to key programming you need to know what you doing there is not too much info in the Diagzone/Prodiag software.   What worked and failed? Here are user reviews. *You are at your risk. We don’t provide technical support to 3rd party software.   Prodiag: Yes It works with prodiag. Prodiag provides usb connection with virtual comport. It works fine to read ECU and gearbox clone. For example, VAG DQ200 gearb...

How to Make Porsche Coding Changes with Launch CRP919X CRP919E

 Instructions on Make Porsche Coding Changes using a Launch CRP919X , CRP919E , CRP919X BT , CRP919E BT scanners. Plugin X431 into OBD 2 Port, Turn Key to Accessory Mode and Wait until VIN is Determined then Hit the Back Arrow in the Upper Left Until You Get to the Next Screen Shown Below  Then select Diagnose (Although you may want to update the unit if updates are available) Then Scroll Down and select Porsche Then Select OK Then Select Automatically Search The Unit should determine the type of 718 you have and then Select OK Then Select System Selection Then Select the appropriate System for the Code you want to adjust (Note: This is the system listed in the instructions below such as Front-end Electronics, Rear-End Electronics, Instrument Cluster or Air Conditioning) Then select Code/Brush Hiding Then select Brush Hidden/Modified Then find the Code you want to adjust (These are the Codes in the instructions below) Then Make the Change Then Hit the Write Code Button