Skip to main content

Launch X431 Corvette Hydraulic System Flush Procedure

Besides the GM deal tool, do any of the other OBD based tools have this functionality (DCT Hydraulic System Flush Procedure)?

 

*Hydraulic System Flush Procedure. It’s all computer, GM dealers use a scan tool to run the MDI and SPS Programs which initiates the hydraulic system flush procedure. The programs circulate the transmission fluid through the transmission which is circulating all the fluids through the DTC filter before they change it. The program takes about eight minutes to complete. GM requires this procedure to be done by the dealer when the DCT filter is changed.

 

Is there any scan tool that can initiate the hydraulic system flush procedure on the Chevrolet Corvette?

The Launch X431 and Autel MS906 pro (or advanced Maxisys) bidirectional scanners can but they aren’t cheap.

X431 makes a less expensive one that will perform the DCT flush, and some other things like bleeding the brakes.

Launch models CRP919E ($389.00) / CRP919EBT ($439.00) / X431 V ($749.00) will be able to perform the HSF procedure.

Software revision 49.45 and onwards does have the hydraulic flush procedure.

Like the X-431 it performs diagnostics on practically every car currently made so you can diagnose all your vehicles.

 

Creader Elite GM and handheld Launch scanners will not perform HSF on Corvette.

The Launch X-431 will run all the flush and bleed procedures. Plug it into Corvette C8 and it will perform the many functions, including the DCT filter flush.

The Launch update has what appears to be the automated DCT hydraulic flush procedure. Several software versions prior had the flush procedure, but listed the individual steps instead.

Selecting transmission control module brings you here

Launch X431 Corvette Hydraulic System Flush Procedure 1

Selecting special functions brings you here

Launch X431 Corvette Hydraulic System Flush Procedure 2

Selecting hydraulic system flush procedure brings you here. Note the time to run this – which is the same time as the MDI 2 the dealer uses.

The seven individual steps by themselves are no longer listed.

These are the four transmission procedures.

When requesting this procedure, a brief description is given such as engine/trans temps, service brake applied and the time it takes to complete.

Selecting the flush procedure starts the program. It does not open up to the individual steps like the earlier software. The 7 separate procedures were deleted.

Launch X431 Corvette Hydraulic System Flush Procedure 3

Launch CRP919/X431 series scanners can perform Hydraulic System Flush Procedure on 2023 and 2024 Chevy Corvette, but can’t do it on other years.

The ’23 and ’24 cars have the HST software code already in the ECU / TCM, and earlier years don’t. The Launch model referenced can only execute the built-in procedure, but isn’t able to write the procedure into the ECU / TCM like the GM tool can.

You will need the GDS2 and tech2win diagnostic subscription on Techline Connect for the MDI 2 to do it. This is different than the $40 vin unlock for module programming. It’s gets expensive really fast for the diagnostic subscription by the time you get a laptop that’s capable of running Techline Connect.

www.obdii365.com

Labels:

Comments

Post a Comment

Popular posts from this blog

Install Launch X431 SmartLink C J2534 Driver

Launch X431 SmartLink C can be used as a J2534 PassThru device, working together with the PC installed with the OEM diagnostic software to perform the J2534 reprogramming.   Obdii365   shows where to download and how to install the Passthru SAE J2534 driver for LAUNCH X431 Smart Link C passthru adapter (for   PAD VII ) If you have Smartbox 3.0 (old PAD V and   X431 Pro5 ), download J2534 passthru   in the previous post .     How to Download Launch X431 SmartLink C J2534 passthru driver?   Same as smartbox 3.0, you need both installation programs (setup driver and PC tool for update).   1. Download PC tool for update (update smartlink c firmware) Visit   https://en.cnlaunch.com/ Select Products tab->X-431 PAD VII Pull down product information and find   Download Download   Smartlink J2534.zip Install Launch J2534 PC tool Run LAUNCH J2534 program on desktop. Now you can check Smartlink adapter version and update firmware 2. Do...
Post a Comment
Read more

Will Lauch X-PROG3 Work with Diagzone, Xdiag or Prodiag?

Does Launch X431 X-prog3 work with xdiag, diagzone or prodiag activations?  Diagzone compatible xprog3? Is it working with prodiag? Will it work with xdiag? These are frequently asked questions of   Launch X-PROG3   (also called GIII) programmers. X-prog3 is compatible with Multiple X-431 Series   X-431 V ,  X-431 V+ ,   X431 Pro5 ,  X431 ProS ,   X431 Pro3s+ ,  X-431 PAD V ,  X-431 PAD VII , X-DIAG Pro3 diagnostic tablets. This programmer works not only for programming keys, but for working with ECU and gearbox. But when comes to key programming you need to know what you doing there is not too much info in the Diagzone/Prodiag software.   What worked and failed? Here are user reviews. *You are at your risk. We don’t provide technical support to 3rd party software.   Prodiag: Yes It works with prodiag. Prodiag provides usb connection with virtual comport. It works fine to read ECU and gearbox clone. For example, VAG DQ200 gearb...
Post a Comment
Read more

Launch X431 V+ or PIWIS-III for Porsche Diagnosis?

I have the Launch X431 V+ Pros Mini which I purchased new from obdii365 for $1079. I also have a PIWIS III clone V38.90 that i purchased from another website for $1429. I purchased the Launch X431 V+ with the intent of using it to flash a used control module for my car. When I discovered that the Launch X431 V+ could not do that I purchased a PIWIS III clone with the intention of selling the Launch X431 V+ but I have not got around to selling it yet because it is so much easier to use then the PIWIS III.Here is what I have done so far with each one. Launch X431 V+ : Cleared all the fault codes stored in the car. Activated the Aux setting in PCM (PCM/CDR) I had to add an aux cable to the PCM to make use of this one. Changed the number of flashes for one touch turn signal from 3 to 5 (Front-end Electronics) Activated Comfort entry windows up/down via keyfob (Front-end Electronics) Changed the speed when the doors auto lock, 3 mph to 20 mph (Front-end electronics) Changed the speed when...
Post a Comment
Read more