Original Launch X-431 OBDII Diagnostic Scan Tools

What’s your thoughts on these 3 popular 8 inch diagnostic scanners?   First comes with a table comparison ITEM XTOOL D8 BT Autel MaxiSys MS906 PRO Launch X431 PRO DYNO Image Firmware VCI IVCI-II V200 DBSCar VII CPU 1.8GHz 4-core 2.2GHz+1.8GHz 8-core 2.0GHz 4-core OS Android 5.1 Android 10.0 Android 10.0 RAM 2GB 4GB 4GB Memory 64GB 128GB 64GB Screen 8-inch 8-inch 8-inch Resolutoin 1024*768 1920*1200 1280*800 Front Camera 16Million Pixels Rear Camera 8Million Pixels 16Million Pixels 8Million Pixels Temperature -10 to 50℃ 0 to 50℃ 0 to 50℃ Connection Bluetooth/USB Bluetooth/USB Bluetooth/USB Size 274*175*33.8mm 260*170*30mm 234*166*39.5mm Battery 10000mAh, 3.7V 11600mAh, 3.7V 6300mAh, 7.6V Software All-system Diagnosis √ √ √ Special Function 38 36 37 Active Test √ √ √ Guided Function √ √ √ ECU Coding √ √ √ Repair Data × √ √ Remote Diagnosis √ √ √ DOIP × √ √ CAN FD √ √ √ Online Feedback × √ √ Software Mall × × √ ADAS × √ √ TPMS × × √ Key Programming √ √(Only IMMO in Special Function) √...

Launch Smartlink C is a VCI that is equipped in Launch’s high-end equipment (X431 PAD V/   PAD VII ), giving us a great possibility to perform tasks beyond diagnosis;   for example advanced programming.   In addition, with this J2534 Passthru VCI you can use it in a large number of official brand software and that is why we put it to the test with wiTECH 2, the official FCA software for Dodge, Jeep, Chrysler, Fiat brand vehicles.     Preparation: 1.Download Launch smartlink c software driver on cnlaunch.com or here 2. pay for the 3 day subscription to tech authority. register your laptop with witech, assign your subscription to your laptop     How to set up   Launch SmartLink C   with witech 2.0? The first thing we do is connect the VCI to the vehicle. Connect the cable with our VCI with J2534, now we connect the VCI to a computer with the sofware driver installed. Software will recognize the VCI as connected. open the Witech 2.0 software des...

 Toyota Techstream V18.00.008 software was tested working with Launch X431 SmartLink C J2534 passthru device. First of all, download and install SmartLink C J2534 driver here http://blog.obdii365.com/2023/04/12/download-launch-x431-smartlink-c-j2534-passthru-driver/ then download and install Techstream 18.00.008 http://blog.obdii365.com/2023/02/01/free-download-toyota-techstream-v18-00-008/ Run J2534Plus passthru check device is connected Run techstream software, go to VIM Selection, select VCI as J2534Plus Software is ready to use

When do you need to connect   Launch X431 Pro5   via USB?   Case 1: When you need to establish an ECU/TCU cloning with   X431 Pro5+ X-prog3 , the system will ask you to connect the USB to scanner. There is a port on the side of pro5. The port is used to charge the battery. You can also connect it with USB through an OTG adapter. Case 2: X431 Pro5 has built-in BMW and Benz online programming. Some users reported that E series onling coding/programming goes fine, but failed to program F series online, i.e failed to program F series BMW 525d 2014 and BMW 535d, F series 2013 (error Ethernet Communication Test Failed). To program BMW F series you’d better connect ENET cable via USB instead of wireless mode. Using otg cable for good connection. It’s going to work. There is an Ethernet cable in the package. The ENET cable cannot be connected to the port directly You will need a OTG converter like this:   Case 3: When need to transfer data from   Lauch X431 Pro 5 ...

How-to: program Porsche Cayenne 2011-2017 5M48H key with   Launch X431 IMMO Plus / IMMO Elite   with X-prog3.   Connect IMMO tablet with x-prog3 programmer Step 1: Read IMMO Data Select Porsche software->IMMOBILIZER function->Cayenne->2011-2017->Read IMMO Data->5M48H Check wiring diagram Follow wiring diagram to connect 5M48H immo module with x-prog3 (need to remove component) Backup EEPROM Data Step 2: Generate Dealer Key Select Generate dealer keys Upload eeprom data read in step 1 Place the new key into x-prog3 programmer Select an unused key position to generate key Generate dealer key completed. Step 3: Learn key Select Learn keys All keys should be learned. Turn on emergency indicators Upload eeprom data again Input number of keys need to learn: 2 Insert original key and turn on ignition switch Insert new key and turn on ignition switch. You will see 2- keys learned on dashboard. www.obdii365.com