Skip to main content

Porsche Macan Coding by Launch X431 vs PIWIS

Launch X431 and PIWIS which is better for Porsche Macan Coding?

 

First of all, check Porsche Macan coding capabilities between Launch X431 and PIWIS

LAUNCH X431PIWIS


Front End ElectronicsBCM vorneValueRelatedDescription
WWS CodingWWS-Codierung


WWS-coding-Teardrop Function activeWWS-Codierung Traenenfunktion aktivYes
Enable automatic delayed extra wipe to clean windshield





Coding



Coding_0



Coding-Comfort functions-Window comfort opening
Yes
Enable automatic window roll down by pressing and holding unlock on keyfob
Coding-Comfort functions-Window comfort closing
Yes
Enable automatic window roll up by pressing and holding lock on keyfob
Coding-Comfort functions-Roof system comfort opening
Yes
Enable automatic sunroof open by pressing and holding unlock on keyfob
Coding-Comfort functions-Roof system comfort closing
Yes
Enable automatic sunroof closing by pressing and holding unlock on keyfob
Exterior lighting DRL with marker lightAußenbeleuchtung TFL mit BegrenzunglichtYes
Enable DRL with Markers On
Coding-Exterior lighting-DDL Specification
No
Disable DRL with Light Switch Off
Coding-Exterior lighting-Exterior lighting: SML flashes in syncAussenbeleuchtung SML mitblinkendYes
Enable side marker blinker with turn signal
Coding-General-Acoustic feedback for locking
Yes
Enable acoustic feedback on locking (No disables lock chirp)
Exterior lights parameters-One Touch flashing cycles
Number
Change number of One Touch Flashing Cycles (Default 3)





Extended Codings



Extended codings-FLA codings-High beam assistant (FLA) present
Yes
Enable High Beam Assist
Rear End ElectronicsBCM ruckValueRelatedDescription
Codiertabelle



Exterior lighting



Exterior Lights, DD lights as marker light
Yes
Enable DRL 4-Point LED’s when headlights on
Exterior lights parameters



Dimming value for DD lights as marker light
100
Dimming value, set to 100 for full intensity
Instrument ClusterKombiinstrumentValueRelatedDescription
Extended codings



Extended codings_0



Extended codings-Max. boost pressureWeitere Codierungen: Max. Ladedruck1.66BARRaise max boost gauge reading to 24PSI (for aftermarket tunes)
Extended codings-Sport boost pressureWeitere Codierungen: Ladedruck Sport1.66BARRaise max boost gauge reading to 24PSI (for aftermarket tunes)





Board computer display configuration key 1_0



BC Configuration byte 8-Door unlocking setting
On
Enables the unlocking of all doors with single press of keyfob
BC Configuration byte 9-locking-mirror fold-in
On
Auto fold mirrors when doors locked (requires additional coding)
BC Configuration byte 10-locking relocking time, after door unlocking
30
Change delay for the auto door re-lock if you unlock and don’t open a door (Max 90)
Board computer display configuration key 1_1Bordcomputer Menukonfiguration


BC Configuration byte 4-BC Role G-ForcePerformance-Anzeige -> aktivOn
Enable the G-Force menu (requires additional coding)
BC Configuration byte 13-high beam assistant
On
Enable High Beam Assist
BC Configuration byte 13-Performance DisplayPerformance-Anzeige -> aktivOn
Enable HP & Torque menu (requires additional coding)
BC Configuration byte 22-BC Role Performance Display
On
Enable HP & Torque menu (requires additional coding)





Board computer display configuration key 2_1



BC configuration byte 13 – high beam assistant
On
Enable High Beam Assist
Board computer display configuration key 3_1



BC configuration byte 13 – high beam assistant
On
Enable High Beam Assist
Board computer display configuration key 4_1



BC configuration byte 13 – high beam assistant
On
Enable High Beam Assist





Board computer display configuration factory setting



BC configuration byte 13 – high beam assistant
On
Enable High Beam Assist





Board computer menu configurationBordcomputer Menukonfiguration


Board computer menu configuration_0



Board computer menu configuration byte 0-boost pressure (bargraph)

Yes
Enable Boost Pressure Bargraph in Vehicle Menu
Board computer menu configuration byte 2-mirror fold-inByte 2 Siegel einklappen -> aktivYes
Auto fold mirrors when doors locked (requires additional coding)
Board computer menu configuration byte 4-expert menu
Yes
Enable the Expert menu (readout of engine sensors & running values)
Board computer menu configuration byte 4-G-ForceByte 4 G-Force -> aktivYes
Enable the G-Force menu (requires additional coding)
Board computer menu configuration byte 7-Performance DisplayAuswahl Performance-Anziege -> aktivYes
Enable HP & Torque menu (requires additional coding)





Board computer menu configuration 2_1



Board computer menu configuration 2 byte 2-Joker Sport
Yes
Enable Sport Mode activation with Diamond button
Board computer menu configuration 2 byte 2-Joker Sport exhaust
Yes
Enable Sport Exhaust activation with Diamond button
Board computer menu configuration 2 byte 0-high beam assistant
Actuated
Enable High Beam Assist





Warning lamps



indicator lamps coding-High beam assistant
On
Enable High Beam Assist





Dimming-general configurationDimmung – allegemeine Konfiguration


Configuration-All dials whiteKonfiguration zentrales Zifferblatt WeissYesCode 1stEnable backlight on RPM dial (value may also be Not Running)

Konfiguration alle Zifferblatter WeissYesCode 2ndEnable backlight on Speedometer dial (value may also be Not Running) – only if RPM dial enabled





Kodierwert



Kodierwert-Coding byte 2-Driver seatbelt warning
Deactivated
Disable seatbelt warning (Driver)
Kodierwert-Coding byte 2-Passenger seatbelt warning
Deactivated
Disable seatbelt warning (Passenger)
Kodierwert-Coding byte 2-USA seatbelt warning
Deactivated
Disable seatbelt warning LED
Kodierwert-Coding byte 2-Acoustic seatbelt warning
Deactivated
Disable seatbelt warning Chime





PCMHeadUnitValueRelatedDescription
Coding value



Coding value_1



VW Coding Value Textual-Bit field (4)-byte_23_Initial Disclaimer
Off
For older models with PCM3, disable initial disclaimer
VW Coding Value Textual-Bit field (4)-byte_23_Legal Disclaimer
Off
For older models with PCM3, disable navigation disclaimer
PCM/CDR Automatic mirror fold in function
Yes
Add Mirror Retract in PCM 3.1
PCM/CDR Handset settings – Ring tone volume
%
Adjust ring volume from Default 50%
Driver-side Seat Memory
ValueRelatedDescription
Comfort Entry/Exit adjustment travel-E/A adjustment travel in
Number
Changes distance seat moves back in mm from driving position on entry. Default is “26”, I made it “40”.
seat fore/aft adjustment








Rear LidHeckdeckelValueRelatedDescription
System selection REAR LID, for both open and closeAdditional Options (F8) -> Change ms value to 0Deactivated
Disable Hatch/Trunk open and close beeps
Set FFB,ST,FIT,HKIT to INACTIVE








Front Camera
ValueRelatedDescription
CodingKodierwert


Coding value-Lighting assistant codingBank 2-AFS_coding_Light_AssistHBA
Enable High Beam Assist

 

Launch X431 is easier to use, but it does not have as much as coding functions than PIWIS. PIWIS has its specific uses. When you swap Macan headlights from BiXenon to LEDs, headlight commissioning and module coding can only be done with PIWIS. When replace air suspension compressor and rear suspension air bag, you can refill and recalibrate with PIWIS.

If you screw up coding with X431 and can’t go back, PIWIS module auto coding will fix it.

PIWIS language is set to German. Language in X431 for coding is English.

Launch X431 is good for daily use and you also need PIWIS.

Labels:

Comments

Post a Comment

Popular posts from this blog

Install Launch X431 SmartLink C J2534 Driver

Launch X431 SmartLink C can be used as a J2534 PassThru device, working together with the PC installed with the OEM diagnostic software to perform the J2534 reprogramming.   Obdii365   shows where to download and how to install the Passthru SAE J2534 driver for LAUNCH X431 Smart Link C passthru adapter (for   PAD VII ) If you have Smartbox 3.0 (old PAD V and   X431 Pro5 ), download J2534 passthru   in the previous post .     How to Download Launch X431 SmartLink C J2534 passthru driver?   Same as smartbox 3.0, you need both installation programs (setup driver and PC tool for update).   1. Download PC tool for update (update smartlink c firmware) Visit   https://en.cnlaunch.com/ Select Products tab->X-431 PAD VII Pull down product information and find   Download Download   Smartlink J2534.zip Install Launch J2534 PC tool Run LAUNCH J2534 program on desktop. Now you can check Smartlink adapter version and update firmware 2. Do...
Post a Comment
Read more

Will Lauch X-PROG3 Work with Diagzone, Xdiag or Prodiag?

Does Launch X431 X-prog3 work with xdiag, diagzone or prodiag activations?  Diagzone compatible xprog3? Is it working with prodiag? Will it work with xdiag? These are frequently asked questions of   Launch X-PROG3   (also called GIII) programmers. X-prog3 is compatible with Multiple X-431 Series   X-431 V ,  X-431 V+ ,   X431 Pro5 ,  X431 ProS ,   X431 Pro3s+ ,  X-431 PAD V ,  X-431 PAD VII , X-DIAG Pro3 diagnostic tablets. This programmer works not only for programming keys, but for working with ECU and gearbox. But when comes to key programming you need to know what you doing there is not too much info in the Diagzone/Prodiag software.   What worked and failed? Here are user reviews. *You are at your risk. We don’t provide technical support to 3rd party software.   Prodiag: Yes It works with prodiag. Prodiag provides usb connection with virtual comport. It works fine to read ECU and gearbox clone. For example, VAG DQ200 gearb...
Post a Comment
Read more

How to Make Porsche Coding Changes with Launch CRP919X CRP919E

 Instructions on Make Porsche Coding Changes using a Launch CRP919X , CRP919E , CRP919X BT , CRP919E BT scanners. Plugin X431 into OBD 2 Port, Turn Key to Accessory Mode and Wait until VIN is Determined then Hit the Back Arrow in the Upper Left Until You Get to the Next Screen Shown Below  Then select Diagnose (Although you may want to update the unit if updates are available) Then Scroll Down and select Porsche Then Select OK Then Select Automatically Search The Unit should determine the type of 718 you have and then Select OK Then Select System Selection Then Select the appropriate System for the Code you want to adjust (Note: This is the system listed in the instructions below such as Front-end Electronics, Rear-End Electronics, Instrument Cluster or Air Conditioning) Then select Code/Brush Hiding Then select Brush Hidden/Modified Then find the Code you want to adjust (These are the Codes in the instructions below) Then Make the Change Then Hit the Write Code Button
Post a Comment
Read more