Skip to main content

Launch X431 V 8 inch tablet WiFi & Bluetooth Setup Manual

How to setup WiFi & Bluetooth in the 2017 Launch X431 V 8 inchscan tool for vehicle diagnosis? Here is the WiFi & Bluetooth setup manual for reference.

Part 1: How to set up Wi-Fi in the Launch X431 V 8 inch scan tool

 Note: If you don't need to use Wi-Fi for a while, you can turn it off to conserve
battery life.

X-431 V has built-in Wi-Fi that can be used to get online. Once you're online,
you can register your X-431 V, browse the Internet, get apps, send email and
check for software updates.

I. Connect to a Wi-Fi network
1. On the home screen, tap Settings > WLAN.
2. Slide the Wi-Fi switch to ON, X-431 V will start searching for available
wireless networks.
3. Select a wireless network,
- If the chosen network is open, X-431 V will connect automatically;
- If the selected network is encrypted, a network password will need to be
entered.
4. When "Connected" appears, tap the Enter button to exit and return to the home screen.

Note: When Wi-Fi is not required, this should be disabled to conserve battery
Power.
Once it is connected successfully, tap the Wi-Fi network from the list to view its
name, link speed, security type, IP address etc.
When this tool is in range, it will connect to the previously linked network
Automatically.

II. Disconnect from a Wi-Fi network
1. On home screen, tap Settings > WLAN.
2. Tap the network with a Connected status, then tap "Disconnect"

III. Vehicle diagnosis via WiFi

launch-x431-v-diagnosis-via-Wifi


Part 2: How to perform Bluetooth setting in the new LaunchX431 V scan tool

I. Bluetooth setting
Enter X-431 V Bluetooth setting screen ("Settings" --> "Bluetooth"), slide the
Bluetooth switch to ON and X-431 V will start searching available Bluetooth
device, tap the desired connector to pair.

By default, the Bluetooth name is 98549*****00 (where ***** stands for 5 digits.).
Note: In case no Bluetooth setting is done before diagnostic software is launched,
you can also configure it while using the software.

II. Car diagnosis via Bluetooth
Tap --> "Diagnostic" to enter the vehicle selection page.
Take Demo as an example to demonstrate how to diagnose a vehicle.
1). Tap the "DEMO", the following dialog box appears:
tap-demo
2). Tap "DEMO" to ignore Bluetooth connection and jump to the DEMO system selection screen. (Note: No Bluetooth connection is required for DEMO program.)
demo-program
3). Tap "Engine", the system will jump to the function menu.
tap-engine
Read DTC
read-DTC
Read Data Stream
read-data-stream-1
read-data-stream-2

Also, special functions and reset service are available.
Special functions:
Injector test, fuel pump test, purge control solenoid and so on.
Reset service:
Oil Reset Service, Steering Angle Calibration, Electronic Parking Brake Reset, Battery Register / Battery Maintenance, ABS Bleeding, Electronic Throttle Position Reset / Learn, Diesel Particulate Filter (DPF) Regeneration, Tire Pressure Monitor System Reset
http://www.x431creader.com/wholesale/launch-x431-v-8inch-full-system-scanner.html
Labels:

Comments

Post a Comment

Popular posts from this blog

Install Launch X431 SmartLink C J2534 Driver

Launch X431 SmartLink C can be used as a J2534 PassThru device, working together with the PC installed with the OEM diagnostic software to perform the J2534 reprogramming.   Obdii365   shows where to download and how to install the Passthru SAE J2534 driver for LAUNCH X431 Smart Link C passthru adapter (for   PAD VII ) If you have Smartbox 3.0 (old PAD V and   X431 Pro5 ), download J2534 passthru   in the previous post .     How to Download Launch X431 SmartLink C J2534 passthru driver?   Same as smartbox 3.0, you need both installation programs (setup driver and PC tool for update).   1. Download PC tool for update (update smartlink c firmware) Visit   https://en.cnlaunch.com/ Select Products tab->X-431 PAD VII Pull down product information and find   Download Download   Smartlink J2534.zip Install Launch J2534 PC tool Run LAUNCH J2534 program on desktop. Now you can check Smartlink adapter version and update firmware 2. Do...
Post a Comment
Read more

Will Lauch X-PROG3 Work with Diagzone, Xdiag or Prodiag?

Does Launch X431 X-prog3 work with xdiag, diagzone or prodiag activations?  Diagzone compatible xprog3? Is it working with prodiag? Will it work with xdiag? These are frequently asked questions of   Launch X-PROG3   (also called GIII) programmers. X-prog3 is compatible with Multiple X-431 Series   X-431 V ,  X-431 V+ ,   X431 Pro5 ,  X431 ProS ,   X431 Pro3s+ ,  X-431 PAD V ,  X-431 PAD VII , X-DIAG Pro3 diagnostic tablets. This programmer works not only for programming keys, but for working with ECU and gearbox. But when comes to key programming you need to know what you doing there is not too much info in the Diagzone/Prodiag software.   What worked and failed? Here are user reviews. *You are at your risk. We don’t provide technical support to 3rd party software.   Prodiag: Yes It works with prodiag. Prodiag provides usb connection with virtual comport. It works fine to read ECU and gearbox clone. For example, VAG DQ200 gearb...
Post a Comment
Read more

Launch X431 V+ or PIWIS-III for Porsche Diagnosis?

I have the Launch X431 V+ Pros Mini which I purchased new from obdii365 for $1079. I also have a PIWIS III clone V38.90 that i purchased from another website for $1429. I purchased the Launch X431 V+ with the intent of using it to flash a used control module for my car. When I discovered that the Launch X431 V+ could not do that I purchased a PIWIS III clone with the intention of selling the Launch X431 V+ but I have not got around to selling it yet because it is so much easier to use then the PIWIS III.Here is what I have done so far with each one. Launch X431 V+ : Cleared all the fault codes stored in the car. Activated the Aux setting in PCM (PCM/CDR) I had to add an aux cable to the PCM to make use of this one. Changed the number of flashes for one touch turn signal from 3 to 5 (Front-end Electronics) Activated Comfort entry windows up/down via keyfob (Front-end Electronics) Changed the speed when the doors auto lock, 3 mph to 20 mph (Front-end electronics) Changed the speed when...
Post a Comment
Read more